South African Class 8B 4-8-0

CSAR Class 8-L2 4-8-0
South African Classes 8B & 8BW 4-8-0

CSAR Class 8-L2, SAR Class 8B, at the Waterval Boven tunnel, circa 1912
Type and origin
♠ Original locomotive, as built
Superheated, outside admission valves
♣ Superheated, inside admission valves, Class 8BW
Power type Steam
Designer Cape Government Railways
(H.M. Beatty)
Builder Neilson, Reid and Company
North British Locomotive Company
Serial number Neilson, Reid 6351-6360
NBL 15783-15802
Model CGR 8th Class (4-8-0)
Build date 1903
Total produced 30
Specifications
Configuration 4-8-0 (Mastodon)
Driver 2nd coupled axle
Gauge 3 ft 6 in (1,067 mm) Cape gauge
Leading dia. 28 12 in (724 mm)
Coupled dia. 48 in (1,219 mm)
Tender wheels 33 12 in (851 mm) as built
34 in (864 mm) retyred
Wheelbase 46 ft 10 12 in (14,288 mm)
  Engine 23 ft 3 in (7,087 mm)
  Leading 6 ft (1,829 mm)
  Coupled 13 ft 6 in (4,115 mm)
  Tender 14 ft 7 in (4,445 mm)
  Tender bogie 4 ft 7 in (1,397 mm)
Length:
  Over couplers 54 ft 5 in (16,586 mm)
Height ♠ 12 ft 10 in (3,912 mm)
♣ 12 ft 8 in (3,861 mm)
Frame type Bar
Axle load ♠ 12 LT 10 cwt (12,700 kg)
12 LT (12,190 kg)
♣ 12 LT 11 cwt (12,750 kg)
  Leading ♠ 11 LT 18 cwt (12,090 kg)
♣ 12 LT 15 cwt (12,950 kg)
  Coupled 12 LT (12,190 kg)
  1st coupled ♠ 12 LT 9 cwt (12,650 kg)
♣ 11 LT 18 cwt (12,090 kg)
  2nd coupled ♠ 12 LT 10 cwt (12,700 kg)
♣ 12 LT 11 cwt (12,750 kg)
  3rd coupled ♠ 11 LT 19 cwt (12,140 kg)
♣ 11 LT 19 cwt (12,140 kg)
  4th coupled ♠ 11 LT 16 cwt (11,990 kg)
♣ 11 LT 18 cwt (12,090 kg)
  Tender bogie Bogie 1: 18 LT 4 cwt (18,490 kg)
Bogie 2: 19 LT 8 cwt (19,710 kg)
  Tender axle 9 LT 14 cwt (9,856 kg)
Adhesive weight ♠ 48 LT 14 cwt (49,480 kg)
48 LT (48,770 kg)
♣ 48 LT 6 cwt (49,080 kg)
Loco weight ♠ 60 LT 12 cwt (61,570 kg)
60 LT 15 cwt (61,720 kg)
♣ 61 LT 1 cwt (62,030 kg)
Tender weight 37 LT 12 cwt (38,200 kg)
Total weight ♠ 98 LT 4 cwt (99,780 kg)
98 LT 7 cwt (99,930 kg)
♣ 98 LT 13 cwt (100,200 kg)
Tender type XF (2-axle bogies)
XC, XC1, XD, XE, XE1, XF, XF1, XF2, XJ, XM, XM1, XM2, XM3 permitted
Fuel type Coal
Fuel capacity 6 LT (6.1 t)
Water cap 3,000 imp gal (13,600 l)
Firebox type Round-top, Drummond
  Firegrate area 21 sq ft (2.0 m2)
Boiler:
  Pitch ♠ 7 ft (2,134 mm)
♣ 7 ft 1 in (2,159 mm)
  Diameter♣ 5 ft (1,524 mm)
  Tube plates ♠ 11 ft 12 in (3,366 mm)
♣ 11 ft 38 in (3,362 mm)
  Small tubes197: 2 in (51 mm)
115: 2 in (51 mm)
  Large tubes48 Drummond: 2 12 in (64 mm)
18: 5 12 in (140 mm)
Boiler pressure 180 psi (1,241 kPa)
Safety valve Ramsbottom
Heating surface ♠ 1,387.3 sq ft (128.88 m2)
♣ 1,081 sq ft (100.4 m2)
  Tubes ♠ 1,261.9 sq ft (117.23 m2)
♣ 950 sq ft (88 m2)
  Firebox ♠ 125.4 sq ft (11.65 m2)
♣ 131 sq ft (12.2 m2)
Superheater:
  Heating area ♣ 214 sq ft (19.9 m2)
Cylinders Two
Cylinder size18 12 in (470 mm) bore
19 in (483 mm) bore
♣ 20 in (508 mm) bore
♣ 24 in (610 mm) stroke
Valve gear Stephenson
Valve type ♠ Slide - ♣ Piston
Couplers Bell link-and-pin
AAR knuckle (c. 1930s-1950s)
Performance figures
Tractive effort ♠ 23,110 lbf (102.8 kN) @ 75%
24,370 lbf (108.4 kN) @ 75%
♣ 27,000 lbf (120 kN) @ 75%
Career
Operators Central South African Railways
South African Railways
Class CSAR Class 8-L2
SAR Class 8B, Class 8BW
Number in class 30
Numbers CSAR 441-470, SAR 1132-1161
Delivered 1903
First run 1903
Withdrawn 1972
The leading coupled axle had flangeless wheels

The South African Railways Class 8B 4-8-0 of 1903 was a steam locomotive from the pre-Union era in Transvaal.

In 1903, soon after its establishment, the Central South African Railways placed thirty Class 8-L2 4-8-0 Mastodon type steam locomotives in service. In 1912, when they were assimilated into the South African Railways, they were renumbered and designated Class 8B.[1][2][3][4]

Central South African Railways

Upon the establishment of the Central South African Railways (CSAR) in July 1902, soon after the end of the Second Boer War, Chief Locomotive Superintendent P.A. Hyde became the custodian of a mixed bag of locomotives, inherited from the Imperial Military Railways (IMR). These included locomotives which originated with the Selati Railway, the Nederlandsche Zuid-Afrikaansche Spoorweg-Maatschappij (NZASM), the Pretoria-Pietersburg Railway (PPR) and the Oranje-Vrijstaat Gouwerment-Spoorwegen (OVGS or OVSS).[2][5]

Manufacturers

The comparatively small number of serviceable locomotives which were immediately available for service, compounded by the poor condition of many of the original NZASM, PPR, Selati and OVGS locomotives, as well as an expected post-war increase in traffic, led to an order for thirty Cape 8th Class 4-8-0 steam locomotives from Neilson, Reid and Company.[1][2][6]

H.M. Beatty

They were built to the specifications of the 8th Class 4-8-0 Mastodon type, designed by H.M. Beatty, the Chief Locomotive Superintendent of the Cape Government Railways (CGR) from 1896 to 1910, and were the first locomotives to be ordered under the CSAR administration. Since they differed from the Class 8-L1 which had been inherited from the IMR, being equipped with Drummond tubes, these locomotives were designated CSAR Class 8-L2.[1][4]

While they were being built, Neilson, Reid amalgamated with Dübs and Company and Sharp, Stewart and Company to form the North British Locomotive Company (NBL). As a result, the first ten of these locomotives, numbered in the range from 441 to 450, were delivered as built by Neilson, Reid, while the other twenty, numbered in the range from 451 to 470, were delivered as built by NBL, even though all the NBL locomotives were also built at the Hyde Park shops of the former Neilson, Reid.[1][7]

Drummond tubes

When Hyde placed the order for these locomotives, he specified fireboxes equipped with Drummond water tubes. This involved the installation of crossing water tubes into the firebox, as featured on the London and South Western Railway's T9 Class and L11 Class, in an attempt to increase the heating surface area of the water, albeit at the cost of increased boiler complexity. The tubes were arranged in two clusters and angled to aid circulation. Visible exterior evidence of the presence of Drummond tubes was the two offset rectangular inspection covers, attached to the sides of the firebox. They contained stay plugs, serving stays which extended through the tubes from cover to cover through the firebox.[1][2]

The CGR had also experimented with Drummond tubes, by modifying its 6th Class no. 286, and had found that the benefit in improved performance was minimal, while the tubes were inclined to leak and were difficult to maintain. Like the CGR, the CSAR soon learned that the increase in steaming capacity was not sufficient to warrant the additional initial cost and increased maintenance requirements.[1][2]

Apart from the Drummond tubes, the locomotives differed from the Class 8-L1 in a few particulars. Their coupling rods were "H" section instead of rectangular, while their crank pins were slightly larger.[2]

South African Railways

When the Union of South Africa was established on 31 May 1910, the three Colonial government railways (CGR, Natal Government Railways and CSAR) were united under a single administration to control and administer the railways, ports and harbours of the Union. Although the South African Railways and Harbours came into existence in 1910, the actual classification and renumbering of all the rolling stock of the three constituent railways required careful planning and was only implemented with effect from 1 January 1912.[3][8]

In 1912, these locomotives were renumbered in the range from 1132 to 1161 and designated Class 8B on the SAR.[3][4][9]

The Class 8-L2 locomotives, together with the CSAR's Classes 8-L1 and 8-L3 4-8-0 Mastodon type locomotives and all the CGR's 8th Class 2-8-0 Consolidations and 4-8-0 Mastodons, were grouped into ten different sub-classes by the SAR. The 4-8-0 locomotives became SAR Classes 8 and 8A to 8F and the 2-8-0 locomotives became Classes 8X to 8Z.[10]

Modifications

In the SAR era, the Drummond tubes were gradually removed, as and when the boilers required repairs, but the locomotives retained their Class 8B designation.[1]

During A.G. Watson's term as the Chief Mechanical Engineer (CME) of the SAR from 1929 to 1936, many of the Class 8 to Class 8F locomotives were equipped with superheated boilers, larger bore cylinders and either inside or outside admission piston valves.[4][10]

The outside admission valve locomotives had their cylinder bore increased from 18 12 inches (470 millimetres) to 19 inches (483 millimetres) and retained their existing SAR classifications, while the inside admission valve locomotives had their cylinder bore increased to 20 inches (508 millimetres) and were reclassified, with a "W" suffix added to their existing SAR classifications.[4][10]

Of the Class 8B locomotives, nine were equipped with superheating, 19 inches (483 millimetres) bore cylinders and outside admission piston valves, while retaining their Class 8B classification.[10]

Six locomotives were equipped with superheating, 20 inches (508 millimetres) bore cylinders and inside admission piston valves and were reclassified to Class 8BW.[10]

Service

In SAR service, the 4-8-0 Class 8 family of locomotives served on every system in the country and, in the 1920s, became the mainstay of motive power on many branchlines. Their final days were spent in shunting service. They were all withdrawn from service by 1972.[4]

Works numbers

The Class 8B and 8BW builders, works numbers, renumbering and superheating modifications are listed in the table.[3][6][10]

Illustration

The main picture is a scan of a c. 1935 post card, showing a SAR Class 8B, ex CSAR Class 8-L2, banking at the Waterval Boven tunnel. The pictures below illustrate unmodified locomotives with Drummond tubes as well as superheated locomotives with outside admission piston valves (no. 1155) and inside admission piston valves (no. 1153).

References

  1. 1 2 3 4 5 6 7 Holland, D.F. (1971). Steam Locomotives of the South African Railways, Volume 1: 1859-1910 (1st ed.). Newton Abbott, Devon: David & Charles. pp. 56, 127. ISBN 978-0-7153-5382-0.
  2. 1 2 3 4 5 6 Espitalier, T.J.; Day, W.A.J. (1945). The Locomotive in South Africa - A Brief History of Railway Development. Chapter VI - Imperial Military Railways and C.S.A.R. (Continued). South African Railways and Harbours Magazine, January 1945. pp. 11-16.
  3. 1 2 3 4 Classification of S.A.R. Engines with Renumbering Lists, issued by the Chief Mechanical Engineer's Office, Pretoria, January 1912, pp. 8, 12, 15, 41 (Reprinted in April 1987 by SATS Museum, R.3125-6/9/11-1000)
  4. 1 2 3 4 5 6 Paxton, Leith; Bourne, David (1985). Locomotives of the South African Railways (1st ed.). Cape Town: Struik. pp. 48–49. ISBN 0869772112.
  5. Durrant, A E (1989). Twilight of South African Steam (1st ed.). Newton Abbott, London: David & Charles. p. 8. ISBN 0715386387.
  6. 1 2 Neilson, Reid works list, compiled by Austrian locomotive historian Bernhard Schmeiser
  7. North British Locomotive Company works list, compiled by Austrian locomotive historian Bernhard Schmeiser
  8. The South African Railways - Historical Survey. Editor George Hart, Publisher Bill Hart, Sponsored by Dorbyl Ltd., Published c. 1978, p. 25.
  9. Holland, D.F. (1972). Steam Locomotives of the South African Railways, Volume 2: 1910-1955 (1st ed.). Newton Abbott, Devon: David & Charles. p. 139. ISBN 978-0-7153-5427-8.
  10. 1 2 3 4 5 6 South African Railways and Harbours Locomotive Diagram Book, 2'0" & 3'6" Gauge Steam Locomotives, 15 August 1941, as amended
Wikimedia Commons has media related to South African Class 8B (4-8-0).
This article is issued from Wikipedia - version of the 5/22/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.