Tank transporter

M19 Tank Transporter, composed of an M20 tractor unit and M9 semi-trailer

Antar tank transporter

Oshkosh M1070 tractor unit of the HET heavy equipment and tank transporter system

A tank transporter is a combination of a heavy tractor unit and mating semi-trailer, typically a Lowboy (trailer), used for transporting tanks. Some also function as tank recovery vehicles, the tractors of which may be armored for protection in combat conditions.

Used on the road, tank transporters limit the wear on tracks and drive trains of tracked vehicles. They also conserve fuel, are less damaging of road surfaces, and are overall more efficient moving tanks at high speeds than tanks operating at them even if they are capable.

Chassis designs

Three chassis designs have been used, generally in this order over time as loads became heavier, although there are exceptions.

Rigid chassis

The lighter tanks of the inter-war period were carried on simple rigid flatbed lorries.

Trailers

The A39 Tortoise being towed on a trailer by two Diamond Ts during trials in BAOR, 1948

As the weight of tanks became too much for lorry chassis, separate trailers were developed. These carried the entire weight of the tank on their own wheels, putting no weight onto the tractor unit. They are pulled by a ballast tractor connected to a drawbar.

The simplest trailer designs have only two axles, but heavier loads frequently require more than this. Multiple wheels per axle are common, usually four, sometimes eight.

One advantage of ballast tractors is that they're capable of double-heading, where two tractor units are coupled to pull a particularly heavy trailer.

Steering

Some designs, such as the 1928 Aldershot design,^[1] grouped pairs of axles at each end of the trailer.

Others, such as the 70-ton Cranes trailer illustrated here beneath the Tortoise had five axles, spaced along the length of the trailer.^[2] The end-wheel designs have the advantages of better ability to cross rough ground and steering more easily. Those with axles throughout their length must have suspension that allows the axles to move and also allowing some steering. This makes them more complicated to manufacture. Placing the wheels at the ends also allows the chassis to dip down into a "well", giving a lower centre of gravity during transport. The Cranes' trailer had a frame split into two sections of two and three axles, with a further carrying bed above them. The outermost four axles had Ackermann steering for their wheels.

The German Sd.Ah.116 trailer of World War 2 (illustrated below.) went so far as to have steersman's position on the rear bogie, covered by the canvas tilt just visible in the background of the photograph.

Semi-trailers

Lowboy (trailer) semi-trailer

The ballast tractor for a drawbar trailer must weigh comparably to its load if it's to have traction, which means that the total load might be as much as twice the useful payload. By using a Lowboy (trailer) semi-trailer instead, some of the load's weight is instead carried by the tractor. This avoids the need for ballasting it, making a greater proportion of the total weight available for the payload.

The simplest semi-trailer is "half of a trailer", having wheels at the rear only and an articulated connection to the tractor unit. A strong metal post or kingpin on the trailer fits into a socket or fifth wheel on the tractor.

Semi-trailers cannot be moved on their own, or pushed and pulled by ballast tractors. They are only mobile when connected to the correct tractor unit, which can limit their use in recovery.

To keep the load's centre of gravity low, gooseneck trailers are used. These have a low horizontal loadbed, with a central spine that rises up at the front to connect to the fifth wheel.

As for drawbar trailers, it's simplest if all the axles of a semi-trailer are concentrated at the rear, away from the tractor unit. The sheer weight of some though requires more and more axles, and these may then need steering gear at the front.

Loading

Ramps

The simplest means of loading the transporter is with a pair of hinged ramps at the rear. The load then drives up and on under its own power. As tracked vehicles exist for their mobility across obstacles, they have no difficulty in doing this.

Tilt beds

The Cranes trailer described above uses an entire see-saw tilting bed (and two small ramps). A manual hydraulic pump tilts the empty bed, bringing the loading end close to the ground. The tank drives up, then once past the see-saw fulcrum the bed tilts back under its weight.

Demountable axles

Loading a StuG III onto a Sd.Ah.116 demountable trailer, 1943

Some designs use a demountable axle, where the axle detaches from the bed of the trailer. Access to the load bed is now through low ramps, without needing to climb over the height of the wheels. Again, the intention is to keep centre of gravity low.

Power for loading

Loading a disabled vehicle by pushing with an armoured recovery vehicle of the German Army

An operational vehicle can be driven on-board under its own power. This is a delicate operation, particularly with tracks, as their precise steering is limited. In particular neutral steering, where one track goes forward and one backward causing the tank to turn on the spot, is likely to either damage the loadbed or to cause the vehicle to fall off.

A few transporters have been fitted with winches for loading, but this is uncommon.^[3] More usually a disabled vehicle is loaded with the assistance of a recovery tractor, either winching or pushing it on board.

Tank recovery vehicles

An M26 armoured tank transporter tractor unit

Some tank transports are equipped with winches or cranes to also serve as tank recovery vehicles. Some are armoured recovery vehicles. Tanks are usually deployed in groups, with an equal number of transporters to support them. Recovery vehicles are more complex and more expensive and thus only a limited number are produced.

For similar reasons, tank transporters are rarely armoured to recover tanks under fire, although tracked recovery vehicles frequently are. A rare few have been, such as the M26 "Dragon Wagon" of World War Two.

Individual models

• 
  Diamond T M20 ballast tractor
• 
  FTF tank transporter tractor unit built by Floor Truck Factory in the Netherlands
• 
  The FTF tractor had a 475 HP Detroit Two-Stroke Diesel engine with Roots blower
• 
  Scammell Contractor hauling Conqueror ARV2 FV222 Tank Recovery Vehicle(REME owned)

See also

• Artillery tractor
• Flatcar - used to transport tanks where railroad tracks are available
• List of U.S. military vehicles by model number

Further reading

• Baxter, Brian S. (1989). Breakdown: A History of Recovery Vehicles in the British Army. HMSO, for REME Museum. ISBN 0-11-290456-4. 

References

External links

Wikimedia Commons has media related to Tank transporters.