Motorcycle frame

Triton: A Triumph engine in a tubular steel Norton Featherbed frame

A motorcycle frame is a motorcycle's core structure. It supports the engine, provides the hinge points for both front and rear suspension, and supports the rider and any pillion or luggage. Also attached to the frame are the fuel tank and battery. At the front of the frame is found the head tube that holds the pivoting front fork, while at the rear there is a pivot point for the swingarm. Some motorcycles[1] include the engine as a load-bearing stressed member; while some others bikes do not use a single frame, but instead have a front and a rear subframe attached to the engine.[2]

Materials

In the early days, motorcycles were little more than motorised bicycles, and consequently frames were tubular steel. While the use of steel tubing is still common, in modern times other materials such as titanium, aluminium, magnesium, and carbon-fibre, along with composites of these materials, are now used. As different motorcycles have varying design parameters (such as cost, complexity, weight distribution, stiffness, power output and speed), there is no single ideal frame design, and designers must make an informed decision of the optimum choice.[3]

Steel

In Europe and the USA, steel tubing was the default material until recent times. All the major manufacturers (AJS, Ariel, BSA, Matchless, Norton, Sunbeam, Triumph, Velocette, BMW, DKW, Ducati, Moto-Guzzi, Harley-Davidson and Indian) used steel tubing.

Examples

Aluminium

Examples

Carbon fibre

Examples

Magnesium

Magnesium framed Elf 5
Examples

Titanium

Examples

Composite

Greeves 250DCX Sportsman 1962
Examples

Types

Spine or backbone

The motorcycle engine is suspended from a single spine.

Examples

Single cradle

The motorcycle engine is held in a single cradle with a single spine.

Examples

Half-duplex cradle

The motorcycle engine is held in a double cradle with a single spine and single downtube.

Examples
Double cradle frame on Honda CB750

Full duplex cradle

The motorcycle engine is held in place within a pair of separate cradles. The Norton Featherbed frame was the classic example, but many "duplex" frames actually have a single spine beneath the tank.

Examples

Perimeter

Two beams wrap around the engine to joint the steering head and swing arm in the shortest distance possible for better rigidity. Beams are usually made of pressed metal (steel/aluminium). The trellis frame employs the same concept but uses welded members to form a trellis instead of pressed metal.

Examples
Twin-beam Frame on Kawasaki ZX-10R
Aluminum beam frame on Buell Lightning

Beam or twin spar

Twin beams (spars) join headstock to swingarm pivot in as straight and short a line as possible. A beam frame can be very similar to the perimeter frame.

Examples

Pressed

Pressed steel frame on Ariel Arrow

The frame is pressed or stamped from sheet metal to form a car-type semi-monocoque. The frame may be entirely pressed (Ariel Arrow), or may have just a pressed aft section connected to the steering head by a conventional steel tubular spine (Honda Super Cub). Both the Super Cub and the Arrow also have pressed steel forks, instead of conventional telescopic forks.

Examples

Monocoque

Main article: Monocoque

More common in the car world, a monocoque frame comprises a structure where loads are supported through an its external skin.

1944 Piaggio MP5 monocoque chassis
Examples

Semi-monocoque

Main article: Monocoque

If a "monocoque" frame uses additional support, such as tubes or longerons, the frame is more properly called a "semi-monocoque". An example is Peter Williams' semi-monocoque Norton racer.

JPS Norton with semi-monocoque frame

Trellis

Steel trellis frame (red) on a Ducati Monster 1000. The engine is a stressed member.

A trellis frame connects the steering head to the swingarm pivot as directly as possible using metal tube arranged in triangulated reinforcement. Using lattice girder principles, a trellis frame is typically constructed of round or oval section metal tubular segments that are welded or brazed together. A well-designed trellis frame should provide a strong, lightweight structure that simplifies placement of engine & components, and gives good access for maintenance. Although construction of a trellis frame needs a more complicated process than, say, an alloy beam frame, it requires only a simple jig and a competent welder. No heavy capital outlay is required, so a trellis frame is ideal for a model that may be made in relatively small numbers. For this reason, the trellis frame has found favour with European manufacturers, and Ducati in particular.

Some motorcycles, such as the Yamaha TRX850, have hybrid frames that employ alloy castings at the swingarm pivot area. Another variation is to suspend the engine from a trellis frame, but have the swingarm pivot cast into the rear of the engine.

Examples

Engine as a stressed member

Further information: Stressed member engine
Harley-Davidson Model W with structural tubes bolted directly to engine case to complete the frame triangle

For rider comfort, a motorcycle's engine can be mounted on rubber bushings to isolate vibration from the rest of the machine. This strategy means the engine contributes little to frame stiffness, and absorbing rather than dissipating vibration can lead to stress damage to the frame, exhaust pipes, and other parts.[3]

Instead, if the engine is rigidly mounted to the frame, vibrations pass to and are dissipated via the whole frame, and the rider. Rigid mounting allows the engine to contribute to the overall stiffness of the frame. It also becomes possible to mount the swingarm directly to the engine rather than the frame, avoiding the need for frame members extending downward to the swingarm pivot. By increasing the number of mounting points between the engine and frame, vibrations and stress can be better dissipated in the frame, typically creating a triangle between the swingarm in the rear, the cylinder head at the top and the lower crankcase area at the front. If a rigidly mounted engine not only contributes to, but is critical to, the stiffness of the frame, and is an integral part of closing the triangle or trellis structure that transfers force from the headstock to the swingarm, to the point that without the engine the frame would be deformed, the engine is called a stressed member, or a lifted engine. Sharing the load between the engine and frame reduces the overall weight of the motorcycle.[3]

Stressed member engines were pioneered at least as early as the 1916 Harley-Davidson 8-valve racer, and incorporated in the production Harley-Davidson Model W by 1919.[8] This was called a keystone, or diamond, frame.[9][10] The 1946 Vincent Series B Rapide was designed with an advanced chassis, termed a "tour de force for its day,"[11] that included a stressed member engine. During early testing of the 1983 Kawasaki GPZ900R, twin downtubes were included, creating a full cradle, but the downtubes were found to carry little load, so they were removed, relying entirely on the combination of the steel backbone and engine for chassis rigidity.[12] BMW's R1100 series twins of 1994 relieved the frame of stress entirely, with the engine carrying the total load from the front Telelever fork to the rear Monolever.[13][14]

Stiffness

Frame stiffness is a problem for motorcycle designers, as it was for the bicycle frames that motorcycles are descendants of.[15][16]

Modifying the stiffness of a factory-produced frame can be undertaken to improve handling characteristics. This is often done by triangulating the factory frame.[15][17] Triangulation is a technique used in many engineering applications to stiffen structures.[18] However doing so can also have undesirable effects if it overloads other parts of the frame, as a flexible frame acts as a spring to absorb some loads.[19]

Lateral stiffness

In the 21st century, advances like high power engines driving high traction tires,[20] and better-performing suspension components, especially forks,[21] led to a situation where designs with increased overall frame stiffness were made available to consumers. Analysts differ on whether infinite lateral stiffness is desirable,[21] or whether a finite degree of built-in flex is preferable.[22][23]

See also

Notes

Wikimedia Commons has media related to Motorcycle frame.
  1. ↑ Note: ... such as the Ducati 900 SS
  2. ↑ Note: An example is the Vincent HRD
  3. 1 2 3 Cocco 2004.
  4. ↑ Cathcart, Alan (January 2008), "ELF Racing - ELF Motorcycle Chassis Designs - Retrospective;Tracing A Decade Of Radical Racebike Experimentation", Motorcyclist, pp. 50(6), ISSN 0027-2205, retrieved 2011-02-26
  5. ↑ "1971 Titanium Husqvarna; A bike as trick as they got", American Motorcyclist, Westerville, Ohio: American Motorcyclist Association, vol. 60 no. 11, p. 75, November 2006, ISSN 0277-9358, retrieved 2011-02-26
  6. ↑ "1963 Ariel Leader". Retrieved 2008-11-24.
  7. ↑ Brown 1991.
  8. ↑ Rafferty 2001.
  9. ↑ Hunt et al. 2012.
  10. ↑ Abdo 2012.
  11. ↑ Field 2002.
  12. ↑ Walker 2006.
  13. ↑ Stermer 2006.
  14. ↑ Coombs & Shoemark 2002.
  15. 1 2 "Motorcycle frames explained–the frame game", Super Streetbike, September 18, 2009
  16. ↑ Damon Rinard, Sheldon Brown, ed., The Rinard Frame Deflection Test, Harris Cyclery, retrieved 2016-05-11
  17. ↑ Foale 2006.
  18. ↑ Enright 2015.
  19. ↑ Tony Foale (November 1987), Frame mods, Tony Foale Designs, retrieved 2016-05-11
  20. ↑ Kevin Cameron (June 2004), "A short history of chassis flex", Cycle World, 43 (6), p. 18
  21. 1 2 James Parker (August 3, 2011), "Ducati Desmosedici RR: The 85 Percent Solution", Motorcyclist, Suspension components that allow less flex and uncontrolled wheel movement need fewer Band-Aids in the form of compensating motion in the chassis.
  22. ↑ Parks 2015 "[M]otorcycle engineers design in a "tuned" amount of chassis and tire flex. This is helpful because at maximum lean the frame and tire sidewalls are at a better angle to absorb bumps in the road than the suspension system."
  23. ↑ Kevin Cameron (July 2006), "Rossi's woe", Cycle World, 45 (7), p. 18, [L]ateral flexibility must now be intentionally designed into chassis parts to supplement suspension action at high lean angle.

Sources

This article is issued from Wikipedia - version of the 10/15/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.