Balanced audio
Balanced audio is a method of interconnecting audio equipment using balanced lines. This type of connection is very important in sound recording and production because it allows the use of long cables while reducing susceptibility to external noise.
Balanced connections use three-conductor connectors, usually the XLR or TRS phone connector. XLR connectors, for instance, are usually used with microphones because of their durable construction, while TRS jack plugs are usually used for mixer inputs and outputs because of their smaller profile.
Applications
Many microphones operate at low voltage levels and some with high output impedance (hi-Z), which makes long microphone cables especially susceptible to electromagnetic interference. Microphone interconnections are therefore a common application for a balanced interconnection, which cancels out most of this induced noise.
If the power amplifiers of a public address system are located at any distance from the mixing console, it is also normal to use balanced lines for the signal paths from the mixer to these amplifiers. Many other components, such as graphic equalizers and effects units, have balanced inputs and outputs to allow this. In recording and for short cable runs in general, a compromise is necessary between the noise reduction given by balanced lines and the cost introduced by the extra circuitry they require.
Interference reduction
Balanced audio connections use a number of techniques to reduce noise.
A typical balanced cable contains two identical wires, which are twisted together and then wrapped with a third conductor (foil or braid) that acts as a shield. The two wires form a circuit carrying the audio signal; one wire is in phase with respect to the source signal, the other wire is reversed in polarity. The in-phase wire is called non-inverting, positive or "hot" while the out-of-phase wire is called inverting, phase-inverted, anti-phase, negative or "cold". The hot and cold connections are often shown as In+ and In− ("in plus" and "in minus") on circuit diagrams.[1]
![](../I/m/Kabel-Symetrisch.png)
The term "balanced" comes from the method of connecting each wire to identical impedances at source and load. This means that much of the electromagnetic interference will induce an equal noise voltage in each wire. Since the amplifier at the far end measures the difference in voltage between the two signal lines, noise that is identical on both wires is rejected. The noise received in the second, inverted line is applied against the first, upright signal, and cancels it out when the two signals are subtracted.
This differential signal recombination can be implemented with a differential amplifier. A balun may also be used instead of an active differential amplifier device.
The wires are also twisted together, to reduce interference from electromagnetic induction. A twisted pair makes the loop area between the conductors as small as possible, and ensures that a magnetic field that passes equally through adjacent loops will induce equal levels of noise on both lines, which is canceled out by the differential amplifier. If the noise source is extremely close to the cable, then it is possible it will be induced on one of the lines more than the other, and it won't be canceled as well, but canceling will still occur to the extent of the amount of noise that is equal on both lines.
The separate shield of a balanced audio connection also yields a noise rejection advantage over an unbalanced two-conductor arrangement (such as used in typical home stereos) where the shield must also act as the signal return wire. Any noise currents induced into a balanced audio shield will not therefore be directly modulated onto the signal, whereas in a two-conductor system they will be. This also prevents ground loop problems, by separating the shield/chassis from signal ground.
Differential signaling
Signals are often transmitted over balanced connections using the differential mode, meaning the wires carry signals of opposite polarity to each other (for instance, in an XLR connector, pin 2 carries the signal with normal polarity, and pin 3 carries an inverted version of the same signal). Despite popular belief, this arrangement is not necessary for noise rejection. As long as the impedances are balanced, noise will couple equally into the two wires (and be rejected by a differential amplifier), regardless of the signal that is present on them.[2][3] A simple method of driving a balanced line is to inject the signal into the "hot" wire through a known source impedance, and connect the "cold" wire to the signal's local ground reference through an identical impedance. Due to common misconceptions about differential signalling, this is often referred to as a quasi-balanced or impedance-balanced output, though it is, in fact, fully balanced and will reject common-mode interference.
However, there are some minor benefits to driving the line with a fully differential output:
- The electromagnetic field around a differential line is ideally zero, which reduces crosstalk into adjacent cables, useful for telephone pairs.
- Though the signal level would not be changed due to nominal level standardization, the maximum output from the differential drivers is twice as much, giving 6 dB extra headroom.[2]
- Increasing cable capacitance over long cable runs decreases the signal level at which high frequencies are attenuated. If each wire carries half the signal voltage swing as in fully differential outputs then longer cable runs can be used without the loss of high frequencies.
- Noise that is correlated between the two amps (from imperfect power supply rejection, for instance), would be cancelled out.
- At higher frequencies, the output impedance of the output amplifier can change, resulting in a small imbalance. When driven in differential mode by two identical amplifiers, this impedance change will be the same for both lines, and thus cancelled out.[2]
- Differential drivers are also more forgiving of incorrectly wired adapters or equipment that unbalances the signal by shorting pin 2.[2]
Internally balanced audio design
Most professional audio products (recording, public address, etc.) provide differential balanced inputs and outputs, typically via XLR or TRS phone connectors. However, in most cases, a differential balanced input signal is internally converted to a single-ended signal via transformer or electronic amplifier. After internal processing, the single-ended signal is converted back to a differential balanced signal and fed to an output.
A small number of professional audio products have been designed as an entirely differential balanced signal path from input to output; the audio signal never unbalances. This design is achieved by providing identical (mirrored) internal signal paths for both pin 2 and pin 3 signals (AKA "hot" and "cold" audio signals). In critical applications, a 100% differential balanced circuit design can offer better signal integrity by avoiding the extra amplifier stages or transformers required for front-end unbalancing and back-end rebalancing.
Fully balanced internal circuitry has been promoted as yielding 3 dB better dynamic range, as explained above.[4]
Connectors
While 3-pin XLR connectors are the most common balanced connector, quarter-inch (¼" or 6.35 mm) TRS phone connectors (tip-ring-sleeve) are also commonly used. Many hybrid jacks are now designed to take either XLR or TRS phone plugs.
-
2.5, 3.5 and 6.35 mm TRS phone plugs
-
3-pin XLR connectors, female on left and male on right
-
3-pin XLR + 6.35 mm TRS phone hybrid jack.
On TRS phone plugs, the tip is "hot" (positive), the ring is "cold" (negative), and the sleeve is ground (earthed or chassis). If a stereophonic or other binaural signal is plugged into such a jack, one channel (usually the right) will be subtracted from the other (usually the left), leaving an unlistenable L − R (left minus right) signal instead of normal monophonic L + R. Reversing the polarity at any other point in a balanced audio system will also result in this effect at some point when it is later mixed-down with its other channel.
Telephone lines also carry balanced audio, though this is generally now limited to the local loop. It is called this because the two wires form a balanced loop through which both sides of the telephone call travel. Note that the telephone line is balanced for AC (audio) signals but is actually unbalanced at DC, as one wire is fed from the exchange power bus, typically -50 volts, and the other grounded, both via equal value inductors which have about 400 ohms DC resistance, to avoid short-circuiting the wanted AC signal while transmitting DC power to the telephone and allowing simple on/off hook detection.
Data lines, including digital audio, are also frequently balanced, normally using AES3 (AES/EBU) with XLR connectors for pro audio.
Converters
Unbalanced signals can be converted to balanced signals by the use of a balun, often through a DI unit.
If balanced audio must be fed into an unbalanced connection, the electronic design used for the balanced output stage must be known. In most cases the negative output can be tied to ground, but in certain cases the negative output should be left disconnected.[5]
See also
References
- ↑ Self, Douglas (2010). Small Signal Audio Design. Taylor & Francis US. p. 344. ISBN 0240521773.
- 1 2 3 4 Graham Blyth. "Audio Balancing Issues". White Papers. Soundcraft. Archived from the original on 4 December 2010. Retrieved 2010-12-30.
- ↑ "Part 3: Amplifiers". Sound system equipment (Third ed.). Geneva: International Electrotechnical Commission. 2000. p. 111. IEC 602689-3:2001.
Only the common-mode impedance balance of the driver, line, and receiver play a role in noise or interference rejection. This noise or interference rejection property is independent of the presence of a desired differential signal.
- ↑ Grace Design m201 (promotional ad copy) Sweetwater Sound
- ↑ http://www.rane.com/note151.html
External links
- UK Sound And Lighting Community — Article On Balanced Lines
- Ray Rayburn: "Balanced-to-Unbalanced; How to Do it Right"
Rick Chinn: "A Simple Implementation of the Impedance Balanced Output"