Argo (oceanography)

Argo is a system for observing temperature, salinity, and currents in the Earth's oceans which has been operational since the early 2000s. The real-time data it provides is used in climate and oceanographic research.[1][2] A special research interest is to quantify the ocean heat content (OHC).

The distribution of active floats in the Argo array, colour coded by country that owns the float, as of the end of April 2016.

Argo consists of a fleet of almost 4000 drifting profiling floats deployed worldwide. Each Argo float weighs 20–30 kg. Profiling floats are commonly used in oceanography and become "Argo floats" only when they are deployed in conformity with the Argo data policy. In most cases probes drift at a depth of 1000 metres (the so-called parking depth) and, every 10 days, by changing their buoyancy, dive to a depth of 2000 metres and then move to the sea-surface, measuring conductivity and temperature profiles as well as pressure. From these, salinity and density can be calculated. Seawater density is important in determining large-scale motions in the ocean. Average current velocities at 1000 metres are directly measured by the distance and direction a float drifts while parked at that depth, which is determined by GPS or Argos system positions at the surface. The data are transmitted to shore via satellite, and are freely available to everyone, without restrictions.

The Argo program is named after the Greek mythical ship Argo to emphasize the complementary relationship of Argo with the Jason satellite altimeters.

International collaboration

The Argo program is a collaborative partnership of more than 30 nations from all continents (most shown on the graphic map in this article) to provide a seamless global array allowing any country to explore the ocean environment. Argo is a component of the Global Ocean Observing System (GOOS).[3] Argo is coordinated by the Argo Steering Team – an international body of scientists and technical experts that meets once per year. The Argo data stream is managed by the Argo Data Management Team. Overall coordination is provided through the Argo Information Centre, an office belonging to the Intergovernmental Oceanographic Commission which also coordinates GOOS, and the World Meteorological Organization. Argo is also supported by GEO (the Group on Earth Observations), and has been endorsed since its early beginnings by the World Climate Research Programme’s CLIVAR Project (Variability and predictability of the ocean-atmosphere system), and by the Global Ocean Data Assimilation Experiment (GODAE OceanView).

An animation for children was created recently by IMOS (Integrated Marine Observing Strategy, Australia) showing how Argo works.[4]

History

A program called Argo was first proposed at OceanObs 1999 which was a conference organised by international agencies with the aim of creating a coordinated approach to ocean observations. The original Argo prospectus was created by a small group of scientists, chaired by Dean Roemmich, who described a program that would have a global array of about 3000 floats in place by sometime in 2007.[5] The 3000-float array was achieved in November 2007 and was global. The Argo Steering Team met for the first time in 1999 in Maryland (USA) and outlined the principles of global data sharing. The Argo Steering Team made a 10-year report to OceanObs-2009[6] and received suggestions on how the array might be improved. These suggestions included enhancing the array at high latitudes, in marginal seas (such as the Gulf of Mexico and the Mediterranean) and along the equator, improved observation of strong boundary currents (such as the Gulf Stream and Kuroshio), extension of observations into deep water and the addition of sensors for monitoring biological and chemical changes in the oceans. In November 2012 an Indian float in the Argo array gathered the one-millionth profile (twice the number collected by research vessels during all of the 20th century) an event that was reported in several press releases.[7][8] In 2014 the Bio-Argo program was expanding rapidly.[9]

Float design and operation

A schematic diagram showing the general structure of a profiling float as used in Argo

The critical capability of an Argo float is its ability to rise and descend in the ocean on a programmed schedule. The floats do this by changing their effective density. The density of any object is given by its mass divided by its volume. The Argo float keeps its mass constant, but by altering its volume, it changes its density. To do this, mineral oil is forced out of the float's pressure case and expands a rubber bladder at the bottom end of the float. As the bladder expands, the float becomes less dense than seawater and rises to the surface. Upon finishing its tasks at the surface, the float withdraws the oil and descends again.[10]

A handful of companies and organizations manufacture profiling floats used in the Argo program. APEX floats, made by Teledyne Webb Research, are the most common element of the current array. SOLO and SOLO-II floats (the latter use a reciprocating pump for buoyancy changes, unlike screw-driven pistons in other floats) were developed at Scripps Institution of Oceanography. Other types include the NINJA float, made by the Tsurumi Seiki Co. of Japan, and the PROVOR float developed by IFREMER in France. Most floats use sensors made by Sea-Bird Electronics, which also makes a profiling float called Navis. A typical Argo float is a cylinder just over 1 metre long and 14 cm across with a hemispherical cap. Thus it has a minimum volume of about 16,600 cubic centimetres (cm3). At Ocean Station Papa in the Gulf of Alaska the temperature and salinity at the surface might be about 6 °C and 32.55 parts per thousand giving a density of sea-water of 1.0256 g/cm3. At a depth of 2000 metres (pressure of 2000 decibars) the temperature might be 2 °C and the salinity 34.58 parts per thousand. Thus, including the effect of pressure (water is slightly compressible) the density of sea-water is about 1.0369 g/cm3. The change in density divided by the deep density is 0.0109.

The float has to match these densities if it is to reach 2000 metres depth and then rise to the surface. Since the density of the float is its mass divided by volume, it needs to change its volume by 0.0109 × 16,600 = 181 cm3 to drive that excursion; a small amount of that volume change is provided by the compressibility of the float itself, and excess buoyancy is required at the surface in order to keep the antenna above water. All Argo floats carry sensors to measure the temperature and salinity of the ocean as they vary with depth, but an increasing number of floats also carry other sensors, such as for measuring dissolved oxygen and ultimately other variables of biological and chemical interest such as chlorophyll, nutrients and pH. An extension to the Argo project called BioArgo is being developed and, when implemented, will add a biological and chemical component to this method of sampling the oceans.[11]

The antenna for satellite communications is mounted at the top of the float which extends clear of the sea surface after it completes its ascent. The ocean is saline, hence an electrical conductor, so that radio communications from under the sea surface are not possible. Early in the program Argo floats exclusively used slow mono-directional satellite communications but the majority of floats being deployed in mid-2013 use rapid bi-directional communications. The result of this is that Argo floats now transmit much more data than was previously possible and they spend only about 20 minutes on the sea surface rather than 8–12 hours, greatly reducing problems such as grounding and bio-fouling.

The average life span of Argo floats has increased greatly since the program began, first exceeding 4-year mean lifetime for floats deployed in 2005. Ongoing improvements should result in further extensions to 6 years and longer.

As of March 2016, new types of floats were being tested to collect measurements much deeper than can be reached by standard Argo floats. These "Deep Argo" floats are designed to reach depths of 6000 metres, versus 2000 metres for standard floats. This will allow a much greater volume of the ocean to be sampled. Such measurements are important for developing a comprehensive understanding of the ocean, such as trends in heat content.[12]

Array design

The number of profiles gathered by Argo floats south of 30°S (upper curve) compared with profiles gathered by other means (lower). This shows the near elimination of the seasonal bias.

The original plan advertised in the Argo prospectus called for a nearest-neighbour distance between floats, on average, of 3° latitude by 3° longitude.[5] This allowed for higher resolution (in kilometres) at high latitudes, both north and south, and was considered necessary because of the decrease in the Rossby radius of deformation which governs the scale of oceanographic features, such as eddies. By 2007 this was largely achieved, but the target resolution has never yet been completely achieved in the deep southern ocean.[6]

Efforts are being made to complete the original plan in all parts of the world oceans but this is difficult in the deep Southern Ocean as deployment opportunities occur only very rarely.

As mentioned in the history section, enhancements are now planned in the equatorial regions of the oceans, in boundary currents and in marginal seas. This requires that the total number of floats be increased from the original plan of 3000 floats to a 4000-float array.

One consequence of the use of profiling floats to sample the ocean is that seasonal bias can be removed. The diagram opposite shows the count of all float profiles acquired each month by Argo south of 30°S (upper curve) from the start of the program to November 2012 compared with the same diagram for all other data available. The lower curve shows a strong annual bias with four times as many profiles being collected in austral summer than in austral winter. For the upper (Argo) plot, there is no bias apparent.

Data access

One of the critical features of the Argo model is that of global and unrestricted access to data in near real-time. When a float transmits a profile it is quickly converted to a format that can be inserted on the GTS (Global Telecommunications System). The GTS is operated by the World Meteorological Organisation, or WMO, specifically for the purpose of sharing data needed for weather forecasting. Thus all nations who are members of the WMO receive all Argo profiles within a few hours of the acquisition of the profile. Data are also made available through ftp and WWW access via two Argo Global Data Centres (or GDACs), one in France and one in the US.

About 90% of all profiles acquired are made available to global access within 24 hours, with the remaining profiles becoming available soon thereafter.

An actual section of salinity along the date line computed from Argo data using the Global Marine Atlas.

For a researcher to use data acquired via the GTS or from the Argo Global Data Centres (GDACs) does require programming skills. The GDACs supply multi-profile files that are a native file format for Ocean DataView. For any day there are files with names like 20121106_prof.nc that are called multi-profile files. This example is a file specific to 6 November 2012 and contains all profiles in a single NetCDF file for one ocean basin. The GDACs identify three ocean basins, Atlantic, Indian and Pacific. Thus three multi-profile files will carry every Argo profile acquired on that specific day.

A user who wants to explore Argo data but lacks programming skills might like to download the Argo Global Marine Atlas [13] which is an easy-to-use utility that allows the creation of products based on Argo data such as the salinity section shown above, but also horizontal maps of ocean properties, time series at any location etc. This Atlas also carries an “update” button that allows data to be updated periodically. The Argo Global Marine Atlas is maintained at the Scripps Institution of Oceanography in La Jolla, California.

Argo data can also be displayed in Google Earth with a layer developed by the Argo Technical Coordinator.

Data results

The number of papers, by year, published in refereed journals and that are extensively or totally dependent on the availability of Argo data as of 30th May 2016.

Argo is now the dominant source of information about the climatic state of the oceans and is being widely used in many publications as seen in the diagram opposite. Topics addressed include air-sea interaction, ocean currents, interannual variability, El Niño, mesoscale eddies, water mass properties and transformation. Argo is also now permitting direct computations of the global ocean heat content.

A notable recent paper was published by Durack and Wijffels and analyses global changes in surface salinity patterns.[14]

They determine that areas of the world with high surface salinity are getting saltier and areas of the world with relatively low surface salinity are getting fresher. This has been described as 'the rich get richer and the poor get poorer'. Scientifically speaking, the distributions of salt are governed by the difference between precipitation and evaporation. Areas, such as the northern North Pacific Ocean, where precipitation dominates evaporation are fresher than average. The implication of their result is that the Earth is seeing an intensification of the global hydrological cycle. Argo data are also being used to drive computer models of the climate system leading to improvements in the ability of nations to forecast seasonal climate variations.[15]

Argo data were critical in the drafting of Chapter 3 (Working Group 1) of the IPCC Fifth Assessment Report (released September 2013) and an appendix was added to that chapter to emphasize the profound change that had taken place in the quality and volume of ocean data since the IPCC Fourth Assessment Report and the resulting improvement in confidence in the description of surface salinity changes and upper-ocean heat content.

See also

References

  1. ↑ Argo Begins Systematic Global Probing of the Upper Oceans Toni Feder, Phys. Today 53, 50 (2000), doi:10.1063/1.1292477
  2. ↑ Richard Stenger (September 19, 2000). "Flotilla of sensors to monitor world's oceans". CNN. Archived from the original on 6 November 2007. Retrieved 2007-10-28.
  3. ↑ "About Argo". Argo: part of the integrated global observation strategy. University of California, San Diego. Retrieved 15 February 2015.
  4. ↑ "Argo Floats : How do we measure the ocean?" (Youtube video). Integrated Marine Observing Strategy. 10 March 2014. Retrieved 8 October 2014.
  5. 1 2 Roemmich, Dean; et al. "On The Design and Implementation of Argo" (PDF). UCSD. Retrieved 8 October 2014.
  6. 1 2 "Archived copy" (PDF). Archived from the original (PDF) on 2013-10-17. Retrieved 2013-09-02. Argo – A decade of progress (community white paper submitted to OceanObs’09
  7. ↑ "One million Argo profiles". British Oceanographic Data Centre. 2 November 2012. Retrieved 8 October 2014.
  8. ↑ "Argo collects its one millionth observation". UNESCO. 21 January 2013. Retrieved 8 October 2014.
  9. ↑ Davidson, Helen (30 January 2014). "Scientists to launch bio robots in Indian Ocean to study its 'interior biology'". The Guardian. Retrieved 8 October 2014.
  10. ↑ "How Argo floats work". UCSD. Retrieved 8 October 2014.
  11. ↑ Archived October 17, 2013, at the Wayback Machine.
  12. ↑ "News & Features | NOAA Climate.gov". www.climate.gov. Retrieved 2016-02-06.
  13. ↑ Scanderbeg, Megan (September 2014). "Argo Global Marine Atlas". UCSD. Retrieved 8 October 2014.
  14. ↑ Durack, P.J.; S.E. Wijffels; R.J. Matear (27 April 2012). "Ocean Salinities Reveal Strong Global Water Cycle Intensification During 1950 to 2000". Science. pp. 455–458. doi:10.1126/science.1212222. Retrieved 8 October 2014.
  15. ↑ "GODAE OceanView". Retrieved 8 October 2014.

External links

Wikimedia Commons has media related to Argo (oceanography).
This article is issued from Wikipedia - version of the 11/29/2016. The text is available under the Creative Commons Attribution/Share Alike but additional terms may apply for the media files.